Project Associate, Electrical
QOSMIC
Posted 20 Nov 2026, 17:20 IST
This job at a glance
QOSMIC is hiring for Project Associate - Electrical (on-site in Bengaluru). It is open to freshers and people with up to 2 years of experience. Degree asked for: B.Tech / B.E. or M.Tech. The posting asks for Circuit design, Embedded systems and C. 1% of the 99 similar fresher jobs posted this week also ask for Circuit design. Pay is not stated.
- Who can apply
- Freshers and up to 2 years · B.Tech / B.E. or M.Tech
- Must know
- Circuit designEmbedded systemsCPythonMATLABC++
- Work
- On-site in Bengaluru
- Pay
- Not stated by the employer.
- Skill demand
- Circuit design1%Embedded systems1%Python1%of 99 similar fresher jobs posted in India this week
- Listed
- 20 Nov 2026 · still open
Sign in free to see which of these skills your resume already shows.
From the original posting on LinkedIn
About the Role
- Fixed Term: 6–12 months
- Location: Bengaluru (on-site)
- Joining Date: Immediate
This role involves designing, simulating, building, debugging, and testing electronics for optical communication terminals, including precision drive and sensing circuits, power supplies, and microcontroller firmware. It is suitable for recent B.Tech or M.Tech graduates seeking hands-on hardware experience. The term may be extended or converted to permanent based on performance and program needs.
Key Responsibilities
- Design and simulate analog circuits using LTspice (op-amp signal chains, sensor front ends, instrumentation amplifiers, active filters, actuator driver stages).
- Design and verify power electronics (buck, boost, flyback converters, LDOs, auxiliary/bias supplies, rail sequencing, current limiting, protection).
- Capture schematics and lay out PCBs in Altium and KiCad, including component selection, stack-up, grounding, partitioning, clearance, decoupling, and manufacturing outputs.
- Bring up and debug boards, including staged power-up, rail verification, soldering, rework, and fault isolation using oscilloscopes, logic analyzers, DMMs, and current-limited supplies.
- Write and debug embedded C firmware on STM32 for bring-up and test (GPIO, timers, ADC/DAC, SPI, I²C, UART, DMA).
- Characterise circuits and subsystems (frequency/step response, noise floor, linearity, temperature drift, driver performance) with data logged and analysed in Python or MATLAB.
- Support closed-loop system testing (calibration, system identification, tuning).
- Run pre-compliance EMI/EMC and environmental checks (conducted/radiated emissions, susceptibility, ESD, thermal) and implement fixes.
- Build test jigs, harnesses, interface boards (RS-422/485, SPI, CAN), and hardware-in-the-loop setups.
- Document designs, test procedures, and results; present at design reviews; maintain version control for design files.
Requirements & Tech Stack
- Analog Fundamentals: Op-amps (gain-bandwidth, slew rate, offset, noise, stability), filters, amplifier design for sensors and actuators.
- Data Converters: Understanding of ADCs and DACs (resolution, sampling, aliasing, references, settling, impact on measurement/control).
- Power Electronics Fundamentals: Linear vs. switching regulators, converter topologies, magnetics/capacitor selection, ripple, efficiency, thermal dissipation, protection.
- Circuit Simulation: LTspice (transient, AC, noise, stability analysis).
- PCB Design: Altium Designer or KiCad (schematic, layout, fabrication, bring-up).
- Board-Level Debugging: SMD soldering/rework, oscilloscopes, logic analyzers, methodical fault isolation.
- Embedded C: On STM32 or similar ARM Cortex-M parts, HAL to register level, on-target debugging over SWD.
- Interfaces: SPI, I²C, UART, working knowledge of RS-422/485 and CAN.
- Simulation Tools: LTspice and Ngspice.
- Firmware Tools: Embedded C, C and C++ (STM32CubeIDE or GCC/Make toolchain, ST-Link or J-Link debugger).
- Bench Tools: Oscilloscope, logic analyzer, DMM, programmable power supply, electronic load, function generator, soldering station, hot-air rework.
- Analysis & Version Control: Python or MATLAB, and Git.
- EMI/EMC Awareness: Noise sources, coupling paths, filtering, shielding, layout practices; IPC standards for PCB design/assembly; component derating.
- Ability to read datasheets, reference manuals, and application notes.
- Clear documentation, honest reporting of results, and rapid learning drive.
Qualifications
- B.Tech/M.Tech in Electrical, Electronics, ECE, or Instrumentation Engineering.
- 0–2 years of experience; strong project or internship work counts.
Nice-to-Have
- Precision motion control or positioning systems.
- Driving reactive loads (motors, actuators).
- Low-noise sensing and signal conditioning for precision measurement.
- Control systems basics (PID, Bode plots, loop stability, filtering).
- Exposure to optical or photonic systems.
- Space or defence hardware exposure (vibration/thermal testing, NASA, ECSS, MIL-STD standards).
- Student satellite, rocketry, or robotics team experience.
- Personal hardware projects.
What We Offer
- Hands-on ownership of flight-bound hardware from prototype to qualification.
- World-class lab facilities and test equipment.
- Mentorship from the core electronics team.
- A clear path to extension or full-time conversion based on performance.
- Collaborative multi-disciplinary research environment.
How to Apply
Send your resume and a brief note about your interests to: careers@qosmic.space. Include links to boards, schematics, or code you have built.