Electrical Engineering Intern

QOSMIC

Bengaluru, Karnataka, IndiaFresher1h agovia LinkedIn

Posted 20 Nov 2026, 17:15 IST

This job at a glance

QOSMIC is hiring for Electrical Engineering Intern (on-site in Bengaluru, internship). It is open to freshers and people with up to 1 year of experience. Degree asked for: B.Tech / B.E. or M.Tech. The posting asks for Embedded systems, Circuit design and Python. 27% of the 99 similar fresher jobs posted this week also ask for Circuit design. Pay is not stated.

Who can apply
Freshers and up to 1 year · B.Tech / B.E. or M.Tech
Must know
Embedded systemsCircuit designPythonMATLABC++C
Work
On-site in Bengaluru · internship
Pay
Not stated by the employer.
Skill demand
Circuit design27%Embedded systems9%MATLAB7%Python4%of 99 similar fresher jobs posted in India this week
Listed
20 Nov 2026 · still open

Sign in free to see which of these skills your resume already shows.

From the original posting on LinkedIn

Company: QOSMIC

Location: Bengaluru (on-site)

Stipend: INR 35,000 per month

Duration: 3–6 months

Joining Date: Immediate

About the Role

  • Own real hardware end-to-end for optical communication terminals.
  • Take a board from idea to validated hardware.
  • Work involves power distribution and protection, precision analog and driver electronics, and microcontroller code.
  • Mentorship from the core electronics team.

Key Responsibilities

  • Design Power Circuits:
  • DC-DC converters and LDOs
  • Load switches and eFuses
  • Current sensing
  • Reverse-polarity, over-voltage and over-current protection
  • Rail sequencing
  • Design Analog Circuits:
  • Op-amp signal conditioning
  • Instrumentation and difference amplifiers
  • Active filters
  • Voltage references
  • Regulated current and voltage sources
  • ADC and DAC front ends
  • Simulate Circuits:
  • Use LTspice for load transients, inrush, protection response, op-amp stability and phase margin, filter response, and noise.
  • Verify simulations against bench measurements.
  • PCB Design:
  • Capture schematics and lay out PCBs in Altium or KiCad.
  • Consider component selection, grounding and return paths, separation of power and sensitive analog sections, current-carrying copper, thermal design, decoupling, and manufacturing outputs.
  • Assemble and Bring Up Boards:
  • Hand soldering and SMD rework.
  • Staged power-up on a current-limited supply.
  • Rail verification and systematic fault isolation.
  • Write Embedded C Firmware:
  • Use STM32 to run and test hardware.
  • Configure ADC sampling, DAC output, PWM, timers, GPIO control, and UART, I²C or SPI communication.
  • Debug Hardware and Firmware:
  • Use oscilloscope and logic analyzer.
  • Probe signals, decode serial buses, measure timing, ripple and noise.
  • Use SWD to step through code on target.
  • Validate Against Specification:
  • Measure efficiency, ripple, line and load regulation, transient response, protection trip points, gain and bandwidth, offset, noise floor, linearity, and thermal performance.
  • Log and analyze data in Python or MATLAB.
  • Build Test Setups:
  • Create jigs, breakout boards, electronic-load arrangements, and harnesses.
  • Run Pre-Compliance Checks:
  • Perform EMI/EMC checks.
  • Document designs, calculations, test procedures, and results.

Requirements & Tech Stack

  • Simulation: LTspice, Ngspice
  • PCB Design: Altium Designer, KiCad
  • Firmware: Embedded C, C and C++ on STM32 (STM32CubeIDE or GCC/Make toolchain), ST-Link or J-Link debugger.
  • Bench Tools: Oscilloscope, logic analyzer, DMM, programmable power supply, electronic load, function generator, soldering station, hot-air rework.
  • Analysis & Version Control: Python or MATLAB, Git.

Qualifications

  • Pursuing or recently completed a B.Tech/M.Tech in Electrical, Electronics, ECE, or Instrumentation Engineering.
  • Real hands-on hardware experience: designed, built, and debugged boards.
  • Strong understanding of analog fundamentals: op-amps, filters, references, current sensing, ADC/DAC.
  • Solid grasp of power fundamentals: linear vs. switching regulators, converter topologies, component selection, ripple, efficiency, thermal dissipation, protection.
  • Experience designing at least two PCBs through schematic, layout, fabrication, and bring-up.
  • Experience with embedded C on STM32 or similar microcontrollers, including configuring peripherals and debugging on target.
  • Proficient in hand soldering (including fine-pitch SMD) and rework.
  • Confident use of oscilloscope, DMM, and bench supply.
  • Ability to delve into datasheets, reference manuals, and application notes.
  • Awareness of IPC standards for PCB design and assembly, component derating, basic EMI/EMC layout practice, and safety around power and batteries.
  • Clear communication, honest reporting, and a drive to learn fast.

Nice-to-Have

  • Experience on a student engineering team (e.g., rocketry, SAE BAJA, Formula Student, solar/electric vehicle, CubeSat, robotics).
  • Experience with battery packs, BMS, motor drives, or power distribution units.
  • Low-noise or precision analog design, or closed-loop analog control.
  • Harness design, crimping, and connector selection for vibration-prone environments.
  • Exposure to space, defence, or automotive standards and environmental testing.

Fresher Jobs in Bengaluru · last 7 days

60 openings · 59 need no experience

Most hiring: Synmac Consultants Pvt. Ltd., Ibis Styles, Ayka Communication

See all 60 →

FirstHire never charges to apply, and real employers don't ask for money for tests, interviews or offer letters. How we list jobs · Report this job